How To Flash LT+3.0 with JungleFlasher 0.1.92.Beta(304) I made these step by step guides to help people flash their drives right from the start using the new JungleFlasher 0.1.92.Beta(304) and LT+3.0 FW. Added Step by step How to connect LiteOn with CK3 + Probe and x360USB pro tutorial Step by step LiteOn flashing tutorial Step by step BenQ flashing Tutorial Tools and Firmware JungleFlasher 0.1.92.Beta(304) Download Latest LT+3.0 & Stock FW Pack:Download -------------------------------------------------------------------------------------------------- Tutorials Connecting Lite-On Lite-On 02510C (74850C, 83850Cv1, 83850Cv2, 93450C) DG-16D2S + CK3 + X360USB Pro. Spoiler 1. Connect the CK3 PMT Cable to your DVD drive Making sure you have it the right way around. The yellow power button on the PMT cable should be closest to the DVD drive Connecting the PMT cable the wrong way around can damage your drive. 2. Connect the other end of the PMT cable to your CK3. 3. Connect your CK3 Probe to the Probe cable that is attached to the PMT cable. 4. Connect the Molex power cable from your PC or from an external Molex power supply to your CK3. 5. Connect the SATA cable from the DVD drive to your X360USB Pro. 6. Connect the USB cable from your X360USB Pro to a USB port on your computer. You are now ready to begin flashing your LiteOn Flashing with JungleFlasher 0.1.92.Beta(304) & LT+3.0 Lite-On Lite-On 02510C (74850C, 83850Cv1, 83850Cv2, 93450C) DG-16D2S CK3 + Probe and X360USB Pro Spoiler Requirements To Flash LiteOn Drives. X360USB Pro A DVD Drive Power source (I will be using the CK3 LITE) CK3 Probe 3 or a Pogo Mo Thoin DIY Probe (PMT) JungleFlasher v0.1.91 Beta (300) The latest X360USB PRO firmware (must be at least v18) Sata Cable USB Cable The x360USB pro is not compolsary but does make connecting your drive easier If you do not have an x360USB Pro you can connect your drive direct to a sata port on your PC. The CK3 and probe however are a must have for LiteOn key extraction you do not need the probe for flashing so if you already have your key you can still update even without the CK3 and Probe. 1. Select the "DVDKey 32" Tab 2. Make sure the USB only check box is ticked and the I/O port is set to 0x000. 3. In the Port Properties section The X360USB pro should be detected as Primary Master and the Firmware version will be displayed, It is best to be using the latest X360USB Pro firmware which is currently v1.8. 4. Check that the "Dummy.bin only" box is ticked The Dummy.bin will be the file that will contain all of the extracted information (key, inquiry, identify & serial). 5. Click the drive refresh buton and JF should now detect and display your drive 6. Click the "Phat Key" button 7. You will now get a pop up message saying do as the message says and click "yes", JF will begin the extraction process. 8. Now press and hold the yellow power button This will cut the power to your drive and you will notice that the light on your probe has now turned off 9. Whilst holding the power button take your CK3 Probe and press it firmly on the MPX01 point 10. Whilst still holding the probe on the MPX01 Release The Power button the CK3 Probe light will come back on and you will now get another pop up saying Do as the message says Remove the probe from the MPX01 Power off the drive again using the yellow power button on the PMT cable Hold the power button in for 5 seconds, then release to power back on Now Press OK 11. your DVD drives data will now been extracted, You will now be prompted to save the Dummy.bin Create a folder on your desktop and save your dummy file there. (The dummy file contains your DVD drive key so keep it safe!) After Clicking save JF will change to the "Firmware 32" tab, auto-load your extracted data (The Dummy.bin you saved with your DVD Key) into the source buffer. 12. You will now be presented with this message Click "yes" and JF will auto-load LT+3.0 into the Target Buffer 13. after JF has loaded your dummy file and LT+3.0 be sure to check that the DVD keys match 14. Click the "MTK Flash 32" tab 15. Click the "Lite-On Erase" Button 16. You will now be presented with the following message If you are totally sure you wish to continue click "Yes" 17. You will be presented with a second message that explains that the drive will be erased and when it sends an intro to the drive by continuing this will also put your drive into vendor mode. when you are ready click "YES" and JF will begin erasing your drive and send the intro to put it into vendor mode. 18. when the drive status is displayed as 0x90 press the yellow power button on your PMT cable for a second and then release, this will power cycle the drive. The status will now change to 0x72 and your drive will switch to vendor mode you are now ready to flash your new firmware. 19. Click the "write" button and JF will begin writing the new FW to your drive. Once JF has written the FW to the drive it will then verify the flash. 20. Finally click the "Outro / ATA Reset" button, JF will now send the outro command to your drive and take it out of vendor mode. Congratulations you have just finished flashing your drive with LT+3.0 happy Gaming! Benq VAD6038 Spoiler 1. First open JungleFlasher v0.1.90 Beta (293) and select the "MTK Flash 32" Tab. 2. Scan the I/O Ports for your drive. If you are using the X360USB Pro to connect the drive be sure you have clicked the USB only check box and the I/O port is set to 0x000. 3. Click the "BenQ Unlock" Tab and JF will send the magic key to your drive and then intro the device too Once done your BenQ drive should be in vendor mode. 4. Now hit the "Read" button to read your drives Old FW and DVD key. Reading 5. Once JF has finished reading the drive it will open a window and ask you to save your Old FW simply make a folder in a location of your choosing and save the Old FW there. 6. Now JF will now automatically switch to the "Firmware Tool 32" Tab You will notice it has auto loaded your old FW into the Source Buffer along with your DVD key it will also ask if you wish to auto-load the Benq LT-Plus FW, Click "Yes". 7. Once JF has finished loading LT+3.0 into the Target Buffer make sure to check that the DVD keys Match and be sure you have the right version of LT+ loaded. 8. Now click back to the "MTK Flash 32" Tab. 9. click the "Write" button, JF will now start writing the new FW to the drive 10. Once JF has finished Writing the new FW to the drive simply click the "Outro / ATA Reset" Button and JF will close the drive and report back that it has once again detected your Benq drive. congratulations! you have just flashed your BenQ drive with LT+3.0 Happy Gaming I hope this helps Tutorial Made By: Ccaveman84 Property Of: www.xpgamesaves.com
Thanks guys When I have time I'm going to try and make one to show how to patch the XGD3's next I hope this one is not to confusing as it was a rush but as I say I will update it soon
yeh mate I added that to the tut this morning as I noticed the same thing Thanks guys hope it was helpful, I made it as it confused me a but to when I flashed my BenQ lol
Hi. I've had my drive flashed by somebody else a couple of times (currently on lt+ 2.0) but i'm going to have a go myself this time. Your guide is very clear and well put together, but my problem is where to actually start from. You assume that we already know how to extract old firmware and dvd key, and that is where i'm stuck. I do not know how to do this but my dvd key was given to me the first time I had my drive flashed (it is written in a .txt file). None of the guides I've seen start from this point. They either start with .bin files or from the very beginning with the extraction of information from the drive using probes etc. Would you be able to help me out with a short guide that shows how start the flashing process when all you have is the dvd key? Thanks
For sure mate I only done this quick guide as it was Christmas day and I was a little drunk lol I will update this guide for you for use with the new JungleFlasher.0.1.91.Beta(300) which can be found here http://www.xpgamesav...ta300-released/ The new JF adds support for LT+3.0 BenQ and LiteOn What drive do you have?
Brilliant guide, considering you were drunk, lol. I have a phat liteon 93450c, which is now 02510c following the dashboard update. I haven't updated the dashboard to the very latest version yet as I know it's recommended to flash back to stock before doing this. I'm assuming I'll be able to download stock firmware for my drive, correct me if i'm wrong. Thanks for the help
I have finished the guide for benq and will be starting on the LiteOn tut shortly you will need to flash to stock, update to the new dash then flash LT+3.0 You can download the latest LT+ fw pack from the first post which contains all stock FW needed for all drives Check back in a while/tomorrow for the LiteOn tut To extract your LiteOn key you will need a CK3 and CK3 probe If you already have the key backup you will not need to worry about the probe
UPDATED! 28/12/11 I changed the guide to be a more in depth step by step tutorial I also added 2 extra tutorials. Each tutorial is in a spoiler as not to take up to much space. Added Step by step How to connect LiteOn with CK3 + Probe and x360USB pro tutorial Step by step LiteOn flashing tutorial Step by step BenQ flashing Tutorial I would very much appreciate it if you guys could read through these as I would like to hear your feedback to to see if there is anything I could change or improve on in these tutorials. http://www.xpgamesav...dpost__p__84482
I have updated the LiteOn guide mate and I have also added the guide in this post just for you as you already have the key you will not need to use the probe as this is only needed for key extraction. Ignore the numbers on the pictures as I pulled the pics from the main guide you only need to follow the steps given and arrows on the pics Remember to flash back to stock first and update if you are not on the latest dashbord and then flash to LT+3.0 Flashing LiteOn When you already have the DVD key Spoiler If you don't have a CK3 you can power your drive using the Xbox console for power If you don't have an X360USB pro you can connect the sata cable to one on your PC 1. Open JF go to the "Firmware Tool 32" tab 2. Click open source FW and load your old FW/DVD key into the source buffer 3. JF should ask if you wish to auto load the LT+ 3.0 FW 4.Click yes and JF should load LT+ 3.0 into the Target Buffer Make sure your source DVD key matches the one in the target buffer if they don't then click spoof source to target and this will copy your DVD key to the new FW 5. Click the MTK Flash tab 6. Click the LiteOn erase button 7. you will get 2 warning messages simply explaining that JF is about to erase your drive and intro it into vendor mode, click yes to continue 8. when the drive status is displayed as 0x90 press the yellow power button on your PMT cable for a second and then release, this will power cycle the drive. If your not using a CK3 with PMT cable you will need to pull the power cable from the drive at this point and re-attach it within a few seconds in order to power cycle. Dont rush when doing this as you do not want to damage the pins in the drives power port. 8.If done correctly the status will now change to 0x72 and your drive will switch to vendor mode you are now ready to flash your new firmware. 9. Click the "write" button and JF will begin writing the new FW to your drive. Once JF has written the FW to the drive it will then verify the flash. 10. Finally click the "Outro / ATA Reset" button, JF will now send the outro command to your drive and take it out of vendor mode. Congratulations you have just finished flashing your drive with LT+3.0 happy Gaming!
Thanks man always glad to help where I can I will update the tutorials in the OP soon to include the guide I just added for goosville with updated pics
Thanks a lot for the guide Ccaveman84, very much appreciated On point 2 where you say to 'click open source FW and load your old FW/DVD key into the source buffer' it looks as though you have loaded a .bin file. As I only have the dvd key written down in a .txt file is this the file I should load, or will I have to manually input this instead?
Nice OK in this case you will want to skip loading to the source buffer instead click "open target" and load LT+3.0 for LiteOn (LTPlus-0251-v3.0.bin) once you have loaded 3.0 into the target buffer click "manual spoofing" and you will be presented with this window Now click "load key.bin" and locate your key.bin and click "OK" you should now have LT+3.0 for LiteOn in the target buffer with your key loaded and spoofed to the firmware Now continue with the tutorial I gave you from step 5 and you should be all good I hope this helps mate Also I have noticed we have not seen anything in the forums from you why not introoduce yourself in the intro section http://www.xpgamesav...-introductions/