CR3 Lite Jumper Settings (Thanks to Team-Xecuter) The CR3 Lite comes with an adhesive foam pad and the positioning in pictures below. We changed the security sticker as so many cheap knock offs were ripping off our design. It fits nicely to the 360 faceplate now if you wish We also used a high quality 48Mhz crystal - once the cheap knock offs hit the market you can be sure they will use the cheap ones which will be very poor performance. Here are the default settings for the LK Solder Jumpers. As past experience by thousands of users has shown, you should try different settings for your setup until you achieve the best performance. It always helps others to post your own personal results. Phat (Non-Jasper) LK1 - Short (Disable Crystal) LK2 - Open (Enable 10 Ohm on CPU_RST) LK3 - Short (C15 Enable) LK4 - All Open (Slim Settings) Phat (Jasper) LK1 - Short (Disable Crystal) LK2 - Short (Disable 10 Ohm on CPU_RST) LK3 - Short (C15 Enable) LK4 - All Open (Slim Settings) Slim (Trinity) LK1 - Short (Disable Crystal) LK2 - Short (Disable 10 Ohm on CPU_RST) LK3 - Open (C15 Disable) LK4 - Short 1-2 (300pF on CPU_RST to GND) or LK4 - All Open Slim (Corona) LK1 - Open (Enable Crystal) LK2 - Short (Disable 10 Ohm on CPU_RST) LK3 - Open (C15 Disable) LK4 - Short 1-2 (300pF on CPU_RST to GND) or LK4 - Short 2-3 (100pF on CPU_RST to GND) or LK4 - All Open The following CPU RESET CLEANER settings were taken from many users experiences and we compiled all the best settings into one easy board. CPU RESET CLEANER (S2 DIP SWITCH) To disable set 1 and 5 On and the rest OFF You can use a mixture of 234 and 678. 1 and 5 must be set to OFF when using a combo. (1) Bypass (2) 1K ohm (3) 2K ohm (4) 3.3K ohm (5) Bypass (6) 470 pf (7) 560 pf (8) 680 pf PLL_BYPASS CLEANER (S4 DIP SWITCH) 100nF has always proven great for Jaspers. I personally have success with 680pF. Others have reported their own better results with all the other values. (1) N/A (2) 680 pf (3) 150 nf (4) 100 nf (Default - Same as CAP solder Jumper on Rev C) (5) 68 nf (6) 47 nf The wire install and setup is the same as the CoolRunner Rev C. DemoN can now directly connect using the ribbon cable that is included with the DemoN (Programming and Enable/Disable feature) ROL can be wired directly to one of the front LED's without any diode. Jasper: Trinity: Corona: - Update: If you are installing to a Corona the yellow wire in the slim pack is too short - use the yellow wire in the phat pack. Thanks to Ubergeek & Team-Xecuter Source link: http://www.xecuter.c...ead.php?t=92428
Hated them to start with but have a Falcon RGH2 & Trinity to do soon so we'll see how that goes Look here for a collective of info on the CR3 Lite: http://www.xpgamesaves.com/topic/56518-cr3-lite-setups-this-needs-your-input-modders
Is this So you can extract the cpu key and dad key from any Xbox 360 abducted essentially rgh any Xbox 360? Sent from my GT-I9300 using Tapatalk 2
I got my slim trinity with cr3 lite got it booting a while back but might give these settings a try to see if it improves the boot timings
With this chip as it is you can only go as far as 14719 But they have made a add on which is in production now which they have gotten the cpu and dvd key from all new dash's There is another chip in production which will incorporate this add on into 1 chip Like this cr3 lite had the cpu cleaner etc incorporated into it when it once was a add on So yeh shortly any box can be done Again