Tattoo TutorialsTutorial Produced By OzModChips Items Needed: 1) 12 5mm flat stainless washers 2) 20 5mm plastic washers 3) 8 M5 x .8 x 16mm machine screws 4) Arctic Silver 5 thermal paste (Radio Shack) 5)Thread lock Super Glue 6)Foam furniture disc (optional) Tools: T10 and T8, T6 Torx [Auto Zone in the Allen key style, cheapest way to get all the sizes] 1) Pliers 2) Phillips screwdriver 3)1/4 inch socket 4)Tin Snips 5)Generic Heat Gun Once you have your case open: Remove the gold T bolts, and ring of light board to release motherboard. Completely remove motherboard from chassis. Flip the board over and pull the x-clamps off with some pliers carefully. (see Scars tut for x-clamp removal, optional).Remove both X-clamps: Next you will need to drill the original x-clamp holes on the chassis, so that your screws will fit. Now superglue two plastic washers on each of the 8 holes on the inside of chassis, use the screws to hold in place till dry. Now the washers will not move. This is also a good time to glue the foam disc to the GFX (left) side of the chassis, as depicted. Glue them down. Hold with bolts till dry. Remove bolts. Now, if you ever need to do this again, you will NOT need to remove the motherboard. Since the bolts are on the outside of the chassis. Now remove the original feet from the heat sinks, with the 1/4 ratchet, and throw them and the x-clamps in the trash. Clean all excess paste from the sinks and the chips. You want the chips to be legible, and mirror finish. I use a q-tip with a little alcohol. Now that your chips are clean. Next, you will need to 're-flow' the board with your heat gun, in the areas outlined in the diagram below. Start with the bottom of the motherboard, and make sure the board is sitting level. Heat gun on high for 3-4 minutes in circular motion. Watch this video for shielding and patterns. Once cool you can re-install your motherboard Put your washers on all the bolts, and push the first four through on the CPU (right) side. Put more washers on the inside on top of the motherboard. Add the thermal paste to the top of the CPU chip, not too much: Now you will need to carefully thread the heat sink on to the screws. Tighten screws hand tight, then torque one 1/4 turn. Don't forget the washer first. You should have one stainless washer at the head of the bolt against the outside of the chassis, and then the glued plastic ones, then one stainless on the board before the CPU heatsink. So, 2 loose washers per screw. Now you can go ahead and put the other 4 bolts through on the GFX side (left). Use the remaining 4 PLASTIC washers, and glue them CAREFULLY to the board. You only need a tiny drop. IMPORTANT : Take our snips and cut a piece of the metal heat shield off from the top of your plastic box case, it will pop right off the case top. You want a small piece that resembles the assembly of your graphics chip set. This piece will go over both chips and allow for more direct pressure. To fit these chips. Add thermal paste to chips, and put the metal piece you cut on top, then put more paste on top of the metal piece. DO NOT PUT THE 2nd HEAT SINK ON "YET" Now you can plug your xbox in (power and AV cable), WITHOUT 2ND HEAT SINK, and turn it on. This will cause an instant 2 red light error (overheat). Unplug everything, and now you can install the 2ND heat sink. Same thing, just hand tight, and then a 1/4 turn. Don't forget the washers, they should be glued down. Once you have done that, plug it back in and test it out. Should work. BUT. If by any chance it gives you 3 red lights. Simply adjust the tourque of the bolts a little tighter, and try again. But at least you don't have to pull the board again..lol. Now you can put the air duct, dvd drive back in, and the case back together. You should be in good working order. Fast forward a few weeks, another E74. Easy to fix now. Pull the case off. Unscrew / remove the heat sink from the GFX chip set (left side). Plug everything in and turn it on so you get 2 red lights. Put the heat sink back on (re-paste optional). Done. I am not stating this is a permanent fix, and as far as I know, this is the best way to fix E74.
This is the way i fix E-74 I made a jig out of an old Xbox 360 chassis , drilled 8 holes into it where the x clamp legs go through and with the use of some nuts and bolts im able to bolt the motherboard down to prevent warping during the heating process. Theres lots of different methods for fixing E74 and everyone seems to have thier own little twists on doing it, but this tutorial covers the basics pretty well. Good job.
yeah thanks me and a couple of me mates tried this method down at the shop like i said its not permanent fix but it will fix it
E74 is a tricky one to fix , sometimes you can cure it first time and never see the error again, and other times it could come back every few hours.
